Home / Shop by part type / Wide Angle (C.V.) Shafts / WC615021
64 HP Wide Angle CV Driveline with Slip Clutch — 1 3/8" x 6 tractor, 1 3/8" x 21 implement, 75"–114"
WC615021 · 6 Series · Wide Angle CV Driveline with Slip Clutch
$1,274
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- 6 Series
- Tier
- Standard
- Position
- Tractor to baler
- End yoke
- Slip clutch 200mm 8in
- Tractor spline
- 1 3/8" x 6
- Implement spline
- 1 3/8" x 21
- Cross journal diameter
- 27/32 mm (1.06/1.26")
- Cross length
- 76/94 mm (2.99/3.70")
- Closed, cross to cross
- 63" (160 cm)
- Open, cross to cross
- 102" (259 cm)
- Closed length (collapsed)
- 75" (191 cm)
- Open length (extended)
- 114" (290 cm)
- Power at 540 rpm
- 64 hp
- Power at 1000 rpm
- 100 hp
- Decoded
- Wide angle with clutch on plain end
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 64 hp at 540 rpm and 100 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| John Deere 572 | Tractor to baler | Standard |
| John Deere 578 | Tractor to baler | Standard |
| John Deere 582 | Tractor to baler | Standard |
| John Deere 592 | Tractor to baler | Standard |
| John Deere 644 | Tractor to baler | Standard |
| John Deere 678 | Tractor to baler | Standard |
| John Deere 744 | Tractor to baler | Standard |
| John Deere 854 | Tractor to baler | Standard |
| John Deere 864 | Tractor to baler | Standard |
| John Deere 960 | Tractor to baler | Standard |
| John Deere 990 | Tractor to baler | Standard |
| New Holland 450 | Tractor to baler | Standard |
| New Holland 630 | Tractor to baler | Standard |
| New Holland 634 | Tractor to baler | Standard |
| New Holland 638 | Tractor to baler | Standard |
| New Holland 644 | Tractor to baler | Standard |
| New Holland 648 | Tractor to baler | Standard |
| New Holland 654 | Tractor to baler | Standard |
| New Holland 658 | Tractor to baler | Standard |
| New Holland BR740 | Tractor to baler | Standard |
| New Holland BR750 | Tractor to baler | Standard |
| New Holland BR770 | Tractor to baler | Standard |
| New Holland BR780 | Tractor to baler | Standard |
| New Holland BR7050 | Tractor to baler | Standard |
| New Holland BR7060 | Tractor to baler | Standard |
| New Holland BR7070 | Tractor to baler | Standard |
| New Holland BR7080 | Tractor to baler | Standard |
| New Holland BR7090 | Tractor to baler | Standard |
| Case IH RB444 | Tractor to baler | Standard |
| Case IH RB454 | Tractor to baler | Standard |
| Case IH RB455 | Tractor to baler | Standard |
| Case IH RB455A | Tractor to baler | Standard |
| Case IH RB464 | Tractor to baler | Standard |
| Case IH RB465 | Tractor to baler | Standard |
| Case IH RB554 | Tractor to baler | Standard |
| Case IH RB564 | Tractor to baler | Standard |
| Case IH RB565 | Tractor to baler | Standard |
| Case IH RBX441 | Tractor to baler | Standard |
| Case IH RBX442 | Tractor to baler | Standard |
| Case IH RBX451 | Tractor to baler | Standard |
| Case IH RBX452 | Tractor to baler | Standard |
| Case IH RBX453 | Tractor to baler | Standard |
| Case IH RBX461 | Tractor to baler | Standard |
| Case IH RBX462 | Tractor to baler | Standard |
| Case IH RBX463 | Tractor to baler | Standard |
| Case IH RBX552 | Tractor to baler | Standard |
| Case IH RBX553 | Tractor to baler | Standard |
| Case IH RBX561 | Tractor to baler | Standard |
OTHER OPTIONS IN THIS SERIES
$1,049
wide angle cv driveline with shear bolt yoke · 1 3/8" x 6 implement end
$1,049
wide angle cv driveline with shear bolt yoke · 1 3/8" x 21 tractor end
$1,049
wide angle cv driveline with shear bolt yoke
$1,274
1 3/8" x 6 implement end
$1,274
1 3/8" x 21 tractor end · 1 3/8" x 6 implement end
$1,274
1 3/8" x 21 tractor end
$1,261
wide angle cv driveline with torque limiter · 1 3/8" x 6 implement end