Home / Shop by part type / Wide Angle (C.V.) Shafts / WC8150
100 HP Wide Angle CV Driveline with Slip Clutch — 1 3/8" x 6 both ends, 77"–116"
WC8150 · 8 Series · Wide Angle CV Driveline with Slip Clutch
$1,629
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- 8 Series
- Tier
- Heavy duty option
- Position
- Tractor to baler
- End yoke
- Slip clutch 200mm 8in
- Tractor spline
- 1 3/8" x 6
- Implement spline
- 1 3/8" x 6
- Cross journal diameter
- 32/36 mm (1.26/1.42")
- Cross length
- 89/106 mm (3.50/4.17")
- Closed, cross to cross
- 63" (160 cm)
- Open, cross to cross
- 102" (259 cm)
- Closed length (collapsed)
- 77" (196 cm)
- Open length (extended)
- 116" (295 cm)
- Power at 540 rpm
- 100 hp
- Power at 1000 rpm
- 160 hp
- Decoded
- Wide angle with clutch on plain end
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 100 hp at 540 rpm and 160 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| John Deere 435 | Tractor to baler | Heavy duty option |
| John Deere 446 | Tractor to baler | Heavy duty option |
| John Deere 447 | Tractor to baler | Heavy duty option |
| John Deere 448 | Tractor to baler | Heavy duty option |
| John Deere 456 | Tractor to baler | Heavy duty option |
| John Deere 457 | Tractor to baler | Heavy duty option |
| John Deere 458 | Tractor to baler | Heavy duty option |
| John Deere 466 | Tractor to baler | Heavy duty option |
| John Deere 467 | Tractor to baler | Heavy duty option |
| John Deere 468 | Tractor to baler | Heavy duty option |
| John Deere 469 | Tractor to baler | Heavy duty option |
| John Deere 535 | Tractor to baler | Heavy duty option |
| John Deere 546 | Tractor to baler | Heavy duty option |
| John Deere 547 | Tractor to baler | Heavy duty option |
| John Deere 556 | Tractor to baler | Heavy duty option |
| John Deere 557 | Tractor to baler | Heavy duty option |
| John Deere 558 | Tractor to baler | Heavy duty option |
| John Deere 566 | Tractor to baler | Heavy duty option |
| John Deere 567 | Tractor to baler | Heavy duty option |
| John Deere 568 | Tractor to baler | Heavy duty option |
| John Deere 569 | Tractor to baler | Heavy duty option |
| Claas Rollant 250RC | Tractor to baler | Heavy duty option |
| Claas Rollant 255RC | Tractor to baler | Heavy duty option |
| Claas Rollant 354 | Tractor to baler | Heavy duty option |
| Claas Rollant 374RF/RC | Tractor to baler | Heavy duty option |
| Claas Rollant 355/375RC | Tractor to baler | Heavy duty option |
| Claas Rollant 455RC | Tractor to baler | Heavy duty option |
| Claas Variant 280RC | Tractor to baler | Heavy duty option |
| Claas Variant 350 | Tractor to baler | Heavy duty option |
| Claas Variant 360RC | Tractor to baler | Heavy duty option |
| Claas Variant 365RC/RF | Tractor to baler | Heavy duty option |
| Claas Variant 370 | Tractor to baler | Heavy duty option |
| Claas Variant 385/380RC/RF | Tractor to baler | Heavy duty option |
| Krone KR100 | Tractor to baler | Heavy duty option |
| Krone KR125 | Tractor to baler | Heavy duty option |
| Krone KR155 | Tractor to baler | Heavy duty option |
| Krone KR130 | Tractor to baler | Heavy duty option |
| Krone KR160 | Tractor to baler | Heavy duty option |
| Krone 1250 | Tractor to baler | Heavy duty option |
| Krone 1250MC | Tractor to baler | Heavy duty option |
| Krone 1500 | Tractor to baler | Heavy duty option |
| Krone 1500MC | Tractor to baler | Heavy duty option |
| Krone 1500V | Tractor to baler | Heavy duty option |
| Krone 1550 | Tractor to baler | Heavy duty option |
| Krone 1800 | Tractor to baler | Heavy duty option |
| Krone F55 | Tractor to baler | Heavy duty option |
| Krone F1250MC | Tractor to baler | Heavy duty option |
| Krone RP1250MC | Tractor to baler | Heavy duty option |
| Krone RP1550MC | Tractor to baler | Heavy duty option |
| Krone V180 | Tractor to baler | Heavy duty option |
| Krone V1500MC | Tractor to baler | Heavy duty option |
| Krone V1800MC | Tractor to baler | Heavy duty option |
OTHER OPTIONS IN THIS SERIES
$1,230
wide angle cv shaft, bare end for clutch · 1 3/4" x 20 tractor end