Home / Shop by part type / Wide Angle (C.V.) Shafts / OH67513020
125 HP Half Shaft, Implement End — 1 3/4" x 20 implement end, 68"–107"
OH67513020 · P675 series · Half Shaft, Implement End
$875
This is one half of a driveline. A implement end (outer drive tube) on its own will not drive the implement — you also need the matching tractor end in the same P675 series. The options are listed below.
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- P675
- Tier
- Upgrade
- Position
- Implement end (outer drive tube)
- End yoke
- 1 3/4" x 20 splines clamp yoke
- Implement spline
- 1 3/4" x 20
- Cross journal diameter
- 36/42 mm (1.42/1.65")
- Cross length
- 89/104 mm (3.50/4.09")
- Closed, cross to cross
- 54" (137 cm)
- Open, cross to cross
- 93" (236 cm)
- Closed length (collapsed)
- 68" (173 cm)
- Open length (extended)
- 107" (272 cm)
- Power at 540 rpm
- 125 hp
- Power at 1000 rpm
- 200 hp
- Decoded
- Plain half shaft, implement end
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 125 hp at 540 rpm and 200 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
COMPLETES THIS DRIVELINE
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| Massey Ferguson 2140 | Implement end | P675 upgrade |
| Massey Ferguson 2160 | Implement end | P675 upgrade |
| Massey Ferguson 2170 | Implement end | P675 upgrade |
| Massey Ferguson 2170XD | Implement end | P675 upgrade |
| Massey Ferguson 2190 | Implement end | P675 upgrade |
| Massey Ferguson 185 | Implement end | P675 upgrade |
| Massey Ferguson 186 | Implement end | P675 upgrade |
| Massey Ferguson 187LB | Implement end | P675 upgrade |
| Massey Ferguson 190LB | Implement end | P675 upgrade |
| Massey Ferguson 2150 | Implement end | P675 upgrade |
| Massey Ferguson 2240 | Implement end | P675 upgrade |
| Massey Ferguson 2250 | Implement end | P675 upgrade |
| Massey Ferguson 2260 | Implement end | P675 upgrade |
| Massey Ferguson 2270 | Implement end | P675 upgrade |
| Massey Ferguson 2270XD | Implement end | P675 upgrade |
| Massey Ferguson 2290 | Implement end | P675 upgrade |
| New Holland 1270P | Implement end | P675 upgrade |
| New Holland 1270 R-S | Implement end | P675 upgrade |
| New Holland 1290P | Implement end | P675 upgrade |
| New Holland 1290R-S | Implement end | P675 upgrade |
| New Holland 9050P | Implement end | P675 upgrade |
| New Holland 9050R | Implement end | P675 upgrade |
| New Holland 9050S | Implement end | P675 upgrade |
| New Holland 9060P | Implement end | P675 upgrade |
| New Holland 9060S | Implement end | P675 upgrade |
| New Holland 9070R | Implement end | P675 upgrade |
| New Holland 9075S | Implement end | P675 upgrade |
| New Holland 9080P | Implement end | P675 upgrade |
| New Holland 9080R | Implement end | P675 upgrade |
| New Holland 9080S | Implement end | P675 upgrade |
OTHER OPTIONS IN THIS SERIES
$875
1 3/8" x 6 implement end
$875
1 3/4" x 6 implement end
$809
half shaft, implement end, less yoke