Home / Shop by part type / Wide Angle (C.V.) Shafts / W67130216
125 HP Wide Angle CV Driveline — 1 3/8" x 21 tractor, 1 3/4" x 6 implement, 68"–107"
W67130216 · P675 series · Wide Angle CV Driveline
$3,177
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- P675
- Tier
- Upgrade
- Position
- Complete driveline
- End yoke
- Complete wide angle shaft
- Tractor spline
- 1 3/8" x 21
- Implement spline
- 1 3/4" x 6
- Cross journal diameter
- 36/42 mm (1.42/1.65")
- Cross length
- 89/104 mm (3.50/4.09")
- Closed, cross to cross
- 54" (137 cm)
- Open, cross to cross
- 93" (236 cm)
- Closed length (collapsed)
- 68" (173 cm)
- Open length (extended)
- 107" (272 cm)
- Power at 540 rpm
- 125 hp
- Power at 1000 rpm
- 200 hp
- Decoded
- Wide angle complete shaft
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 125 hp at 540 rpm and 200 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
Complete shaft. Bare Co page pto16 states the build explicitly: IH67513021 + OH67513634. Both halves already stocked. Dealer cost not yet captured.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| Case IH LBX331P/R/S | Front driveline | P675 upgrade |
| Case IH LBX332P/R/S | Front driveline | P675 upgrade |
| Case IH LBX421S/R | Front driveline | P675 upgrade |
| Case IH LBX422R/S | Front driveline | P675 upgrade |
| Case IH LBX431R | Front driveline | P675 upgrade |
| Case IH LBX432R/S | Front driveline | P675 upgrade |
| Case IH LBX431S | Front driveline | P675 upgrade |
| Case IH BB940AP/AR/AS/P/R/S | Front driveline | P675 upgrade |
| Case IH BB960S/R/AR/AS | Front driveline | P675 upgrade |
| Case IH 590 | Front driveline | P675 upgrade |
| New Holland 1270P | Front driveline | P675 upgrade |
| New Holland 1270 R-S | Front driveline | P675 upgrade |
| New Holland 1290P | Front driveline | P675 upgrade |
| New Holland 1290R-S | Front driveline | P675 upgrade |
| New Holland 9050P | Front driveline | P675 upgrade |
| New Holland 9050R | Front driveline | P675 upgrade |
| New Holland 9050S | Front driveline | P675 upgrade |
| New Holland 9060P | Front driveline | P675 upgrade |
| New Holland 9060S | Front driveline | P675 upgrade |
| New Holland 9070R | Front driveline | P675 upgrade |
| New Holland 9075S | Front driveline | P675 upgrade |
| New Holland 9080P | Front driveline | P675 upgrade |
| New Holland 9080R | Front driveline | P675 upgrade |
| New Holland 9080S | Front driveline | P675 upgrade |
OTHER OPTIONS IN THIS SERIES
$3,177
1 3/8" x 6 tractor end · 1 3/4" x 20 implement end
$3,177
1 3/8" x 6 tractor end
$3,100
wide angle cv shaft, bare implement end · 1 3/8" x 6 tractor end
$3,100
wide angle cv shaft, bare implement end · 1 3/4" x 20 tractor end
$3,100
wide angle cv shaft, bare implement end
$3,177
1 3/4" x 20 tractor end · 1 3/4" x 20 implement end
$3,177
1 3/4" x 20 tractor end
$3,177
1 3/4" x 20 implement end