Home / Shop by part type / Wide Angle (C.V.) Shafts / W671302120
125 HP Wide Angle CV Driveline — 1 3/8" x 21 tractor, 1 3/4" x 20 implement, 68"–107"
W671302120 · P675 series · Wide Angle CV Driveline
$3,177
Specification
- Product family
- Wide Angle (C.V.) Shafts
- Series
- P675
- Tier
- Upgrade
- Position
- Complete driveline
- End yoke
- Complete wide angle shaft
- Tractor spline
- 1 3/8" x 21
- Implement spline
- 1 3/4" x 20
- Cross journal diameter
- 36/42 mm (1.42/1.65")
- Cross length
- 89/104 mm (3.50/4.09")
- Closed, cross to cross
- 54" (137 cm)
- Open, cross to cross
- 93" (236 cm)
- Closed length (collapsed)
- 68" (173 cm)
- Open length (extended)
- 107" (272 cm)
- Power at 540 rpm
- 125 hp
- Power at 1000 rpm
- 200 hp
- Decoded
- Wide angle complete shaft
Match the tractor, not the implement. The shaft’s rating must meet or exceed your tractor’s PTO horsepower. Undersize it and the driveline becomes the part that fails.
Check your PTO speed. This shaft is rated 125 hp at 540 rpm and 200 hp at 1000 rpm. Use the figure for the speed you actually run — they are not interchangeable.
Working it hard? Bare Co advise reducing the rated horsepower by 40% for severe conditions — shock loading, heavy or wet crop, stony ground.
Length
Closed is the shaft fully collapsed — its shortest. Open is fully extended — its longest. Your tractor and implement must sit inside that range at every point through the turn.
Cross to cross is measured between the centres of the two universal joints. Overall is the full length including the end yokes. Most machine specs quote cross to cross.
This shaft trims to length. Measure your machine at its shortest point — the shaft must not bottom out — then cut to suit. You can always take metal off; you cannot put it back.
Complete shaft. Bare Co page pto16 states the build explicitly: IH67513021 + OH67513020. Both halves already stocked. Dealer cost not yet captured.
FITS THESE MACHINES
| Machine | Position | Tier |
|---|---|---|
| Massey Ferguson 2140 | Front driveline | P675 upgrade |
| Massey Ferguson 2160 | Front driveline | P675 upgrade |
| Massey Ferguson 2170 | Front driveline | P675 upgrade |
| Massey Ferguson 2170XD | Front driveline | P675 upgrade |
| Massey Ferguson 2190 | Front driveline | P675 upgrade |
| Massey Ferguson 185 | Front driveline | P675 upgrade |
| Massey Ferguson 186 | Front driveline | P675 upgrade |
| Massey Ferguson 187LB | Front driveline | P675 upgrade |
| Massey Ferguson 190LB | Front driveline | P675 upgrade |
| Massey Ferguson 2150 | Front driveline | P675 upgrade |
| Massey Ferguson 2240 | Front driveline | P675 upgrade |
| Massey Ferguson 2250 | Front driveline | P675 upgrade |
| Massey Ferguson 2260 | Front driveline | P675 upgrade |
| Massey Ferguson 2270 | Front driveline | P675 upgrade |
| Massey Ferguson 2270XD | Front driveline | P675 upgrade |
| Massey Ferguson 2290 | Front driveline | P675 upgrade |
OTHER OPTIONS IN THIS SERIES
$3,177
1 3/8" x 6 tractor end
$3,177
1 3/8" x 6 tractor end · 1 3/4" x 6 implement end
$3,100
wide angle cv shaft, bare implement end · 1 3/8" x 6 tractor end
$3,100
wide angle cv shaft, bare implement end · 1 3/4" x 20 tractor end
$3,100
wide angle cv shaft, bare implement end
$3,177
1 3/4" x 20 tractor end
$3,177
1 3/4" x 20 tractor end · 1 3/4" x 6 implement end
